Microsoft LPF-00004 Betreibershandbuch Seite 20
- Seite / 157
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Page 2 INTRODUCTION
CYBERAMP 380, COPYRIGHT MARCH 2002, AXON INSTRUMENTS, INC.
Below is a partial list of transducers that can be accommodated to the CyberAmp either by AI 400
series SmartProbes or by user-supplied adapters.
Current AI 400 series picoammeter probes.
Ion-selective electrodes calcium, potassium, etc. Use AI 400 series amplifier probes.
Low-impedance electrodes direct connection to BNC inputs.
Measuring instruments direct connection to BNC inputs.
pH use AI 400 series low-noise amplifier probes.
Surface potentials direct connection or AI 400 series low-noise amplifier probes.
Voltage direct connection or AI 400 series low-noise amplifier probes.
Custom adapters can be made for these transducers.
Acceleration piezoelectric, suspended-mass strain gauges.
Audio microphones.
Flow blood, cardiac output, respiratory.
Flow permanent magnet fluid flow transducers.
Force force/strain gauges.
Length LVDTs, linear potentiometers, optical wedges.
Light photodiode amplification.
Oxygen gaseous, solution.
Pressure conventional and semiconductor types.
Rotation RVDTs, rotary potentiometers.
Strain conventional and semiconductor strain gauges.
Temperature thermistors, thermocouples, semiconductor transducers.
Measurement transducers not supported by existing AI 400 series SmartProbes can be supported by
user-supplied adapters. Later in this manual, detailed information is provided for users who wish to
make their own transducer amplifiers and adapters. The current price list and brochure should be
consulted for the available AI 400 series probes and adapters.
Along with support for a wide variety of signal sources, the CyberAmp is designed to provide
unparalleled low-noise performance. To this end, low-noise input circuitry is used in the CyberAmp
itself, supplemented by the ultra-low-noise circuitry available in SmartProbes. The 10 kHz bandwidth
noise of the CyberAmp main unit is a very low 1.4 µV
rms
(9 µV
p-p
), sufficiently low, that many small
signals such as EMG and ECG sources can be directly connected to it. The 0.18 µV
rms
(1.1 µV
p-p
)
noise of the AI 402 differential amplifier probe is extraordinarily quiet, enabling many technically
difficult measurements, such as nerve-cuff recordings.
- CyberAmp 380 1
- Declaration of Conformity 3
- IMPORTANT INFORMATION 5
- RENSEIGNMENTS IMPORTANTS 6
- WICHTIGE INFORMATIONEN 7
- INFORMACION IMPORTANTE 8
- Explanation of symbols 9
- Explication des symboles 9
- Explicación de símbolos 9
- SÉCURITÉ 10
- SICHERHEITS 10
- HINWEISE 10
- SEGURIDAD 10
- COPYRIGHT 11
- VERIFICATION 11
- TABLE OF CONTENTS 13
- INTRODUCTION 19
- Page 2 INTRODUCTION 20
- INTRODUCTION Page 3 21
- FUNCTIONAL DESCRIPTION 23
- General Features 26
- FUNCTIONAL CHECKOUT 29
- TYPICAL CONFIGURATIONS 33
- Supply Voltage 37
- Changing the Fuse 37
- Grounding and Hum 38
- Power-Supply Glitches 39
- Input Coupling 39
- Expansion 40
- Low-Pass Filter 41
- Amplitude Characteristics 42
- Sampling Rate 43
- 10-90% Rise Time 43
- AC Coupling and Autozeroing 44
- 3 dB frequency of 44
- Time Constant 46
- 100 1.6 46
- Saturation 47
- Notch Filter 48
- Overload Detection 49
- Audio Monitor 50
- External Input 51
- Electrode Test 52
- Strain Gauges 55
- Active Probes 56
- Common-Mode Rejection Ratio 57
- Troubleshooting 59
- TRANSDUCERS 61
- Page 44 TRANSDUCERS 62
- TRANSDUCERS Page 45 63
- EMG, EEG, ECG Recording 64
- Nerve Cuffs 65
- Metal Microelectrodes 65
- Page 48 TRANSDUCERS 66
- Pressure 67
- Acceleration 67
- Self Heating 68
- Isolation 68
- Insulation Techniques 68
- AI 400 SERIES SmartProbes 69
- Transducer Adapter 71
- Input Connector Color Scheme 72
- Recommended Input Coupling 73
- Connector 74
- Example Circuits 75
- Basic Thermistor Circuit 76
- Amplifier Probes 78
- Current Probes 79
- Photodiode Amplifier 79
- Linear Potentiometers 80
- Rotary Potentiometers 80
- Panel Switch 81
- Foot Switch 81
- CMD300 CONTROL SOFTWARE 83
- Command-Line Mode 85
- Interactive Mode 85
- Command-File Mode 86
- Command Reference 87
- CMD300 OVERLOAD 91
- CMD300 REPEAT OVERLOAD 94
- QUICK300 CONTROL SOFTWARE 97
- Command Line Options 100
- CyberControl SOFTWARE 101
- Starting CyberControl 102
- Overload Handling 105
- Keyboard Commands 105
- Communications Settings 107
- PC Menus 108
- Macintosh Menus 109
- PROGRAMMER'S GUIDE 112
- Libraries and Example Code 114
- > end of response 116
- AT3F5 24000 118
- 2 4 6 8 10 ... 28000 30000 118
- AT8R06000 121
- D5=-1234500 124
- Implementation Notes 125
- Support Routine Details 125
- Example Programs 129
- SPECIFICATIONS 135
- Page 118 SPECIFICATIONS 136
- Offset range: ±10 V 137
- Page 120 SPECIFICATIONS 138
- SPECIFICATIONS Page 121 139
- Page 122 SPECIFICATIONS 140
- REFERENCES 141
- ADJUSTMENT PROCEDURES 143
- Other Adjustments 144
- CIRCUIT DIAGRAMS Page 127 145
- SERIAL COMMUNICATIONS CABLES 147
- LIST OF FIGURES AND TABLES 149
- WARRANTY 151
- WARNING 153
- INDEX Page 137 155
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Microsoft LPF-00004
(82 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern