Microsoft LPF-00004 Betreibershandbuch Seite 92
- Seite / 157
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Page 74 CMD300 CONTROL SOFTWARE
C
YBER
A
MP
380, COPYRIGHT MARCH 2002, AXON INSTRUMENTS, INC.
The information indicates that for channel number 1 there is an AI 410 SmartProbe attached
to the CyberAmp input connector, its positive input is DC-coupled and its negative input is
grounded. The overall gain is 20 and is composed of a pre-filter gain of 10 and an output gain
of 2. The low-pass filter 3 dB cutoff is set at 10 kHz and the notch filter is bypassed. A +50
mV, input-referred DC offset is added to the input signal after the filter.
The STATUS DEFAULTS command displays information about the COM port being used
for communications and the RS232 bus device number, if any. It also displays information
about the channels selected for commands and whether responses to commands are verbose or
minimum.
The STATUS ID command displays information about the unit itself, but without any channel
specific information.
18)
TEST
NO
TCH
or
TEST
EL
ECTRODE
ON
/
OF
F
TEST NOTCH places the CyberAmp into the notch-filter test mode.
CMD300 waits for a
keystroke and then takes the unit out of the notch-filter test mode, restoring all previous
CyberAmp settings.
TEST ELECTRODE ON starts a 10 Hz test oscillator that injects 1µA of current into both the
positive and negative inputs. It can be used to measure the source resistances of the inputs.
The user should ground either the positive or the negative input to independently measure the
resistances. Following this test, take the unit out of electrode-test mode with TEST
ELECTRODE OFF.
19)
VERBOSE
This command maximizes all CyberAmp responses to commands. In this mode all command
responses are detailed and all commands evoke some confirming CyberAmp response.
20)
ZERO
ZERO commands the CyberAmp to attempt to zero the DC level of the signals on the selected
channels. The program reports the value of the offset prior to zeroing the output of the
channel amplifier. If the signal on a selected channel could not be zeroed in this manner, then
an error is reported for that channel.
- CyberAmp 380 1
- Declaration of Conformity 3
- IMPORTANT INFORMATION 5
- RENSEIGNMENTS IMPORTANTS 6
- WICHTIGE INFORMATIONEN 7
- INFORMACION IMPORTANTE 8
- Explanation of symbols 9
- Explication des symboles 9
- Explicación de símbolos 9
- SÉCURITÉ 10
- SICHERHEITS 10
- HINWEISE 10
- SEGURIDAD 10
- COPYRIGHT 11
- VERIFICATION 11
- TABLE OF CONTENTS 13
- INTRODUCTION 19
- Page 2 INTRODUCTION 20
- INTRODUCTION Page 3 21
- FUNCTIONAL DESCRIPTION 23
- General Features 26
- FUNCTIONAL CHECKOUT 29
- TYPICAL CONFIGURATIONS 33
- Supply Voltage 37
- Changing the Fuse 37
- Grounding and Hum 38
- Power-Supply Glitches 39
- Input Coupling 39
- Expansion 40
- Low-Pass Filter 41
- Amplitude Characteristics 42
- Sampling Rate 43
- 10-90% Rise Time 43
- AC Coupling and Autozeroing 44
- 3 dB frequency of 44
- Time Constant 46
- 100 1.6 46
- Saturation 47
- Notch Filter 48
- Overload Detection 49
- Audio Monitor 50
- External Input 51
- Electrode Test 52
- Strain Gauges 55
- Active Probes 56
- Common-Mode Rejection Ratio 57
- Troubleshooting 59
- TRANSDUCERS 61
- Page 44 TRANSDUCERS 62
- TRANSDUCERS Page 45 63
- EMG, EEG, ECG Recording 64
- Nerve Cuffs 65
- Metal Microelectrodes 65
- Page 48 TRANSDUCERS 66
- Pressure 67
- Acceleration 67
- Self Heating 68
- Isolation 68
- Insulation Techniques 68
- AI 400 SERIES SmartProbes 69
- Transducer Adapter 71
- Input Connector Color Scheme 72
- Recommended Input Coupling 73
- Connector 74
- Example Circuits 75
- Basic Thermistor Circuit 76
- Amplifier Probes 78
- Current Probes 79
- Photodiode Amplifier 79
- Linear Potentiometers 80
- Rotary Potentiometers 80
- Panel Switch 81
- Foot Switch 81
- CMD300 CONTROL SOFTWARE 83
- Command-Line Mode 85
- Interactive Mode 85
- Command-File Mode 86
- Command Reference 87
- CMD300 OVERLOAD 91
- CMD300 REPEAT OVERLOAD 94
- QUICK300 CONTROL SOFTWARE 97
- Command Line Options 100
- CyberControl SOFTWARE 101
- Starting CyberControl 102
- Overload Handling 105
- Keyboard Commands 105
- Communications Settings 107
- PC Menus 108
- Macintosh Menus 109
- PROGRAMMER'S GUIDE 112
- Libraries and Example Code 114
- > end of response 116
- AT3F5 24000 118
- 2 4 6 8 10 ... 28000 30000 118
- AT8R06000 121
- D5=-1234500 124
- Implementation Notes 125
- Support Routine Details 125
- Example Programs 129
- SPECIFICATIONS 135
- Page 118 SPECIFICATIONS 136
- Offset range: ±10 V 137
- Page 120 SPECIFICATIONS 138
- SPECIFICATIONS Page 121 139
- Page 122 SPECIFICATIONS 140
- REFERENCES 141
- ADJUSTMENT PROCEDURES 143
- Other Adjustments 144
- CIRCUIT DIAGRAMS Page 127 145
- SERIAL COMMUNICATIONS CABLES 147
- LIST OF FIGURES AND TABLES 149
- WARRANTY 151
- WARNING 153
- INDEX Page 137 155
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Microsoft LPF-00004
(82 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern