Microsoft LPF-00004 Betreibershandbuch Seite 97
- Seite / 157
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
QUICK300 CONTROL SOFTWARE Page 79
C
YBER
A
MP
380, COPYRIGHT MARCH 2002, AXON INSTRUMENTS, INC.
QUICK300 CONTROL SOFTWARE
The Quick300 spreadsheet program controls the CyberAmp from PC computers that have a DOS
operating system. It presents a spreadsheet that simultaneously shows the values of the most needed
CyberAmp functions. Each cell in the spreadsheet shows the current setting of a function on one
channel. A function is changed by entering a new value in its cell, or by scrolling through the
permissible values. New values are sent to the CyberAmp immediately, so the current state of the
CyberAmp is always shown on the screen.
Installation
If the CMD300 software was installed on a hard disk, as described in the chapter, CMD300 Control
Software, then QUICK300.EXE can be found in a directory called \CMD300. Otherwise, with the
CyberAmp CD in Drive D:, issue the following DOS commands:
MD \CMD300
CD \CMD300
COPY D:\DOS\CMD300\*.*
OPERATION
QUICK300 is run from the DOS command line.
QUICK300
One can return to DOS by choosing File, eXit.
QUICK300 presents the following opening menu.
File SetValues AutoZero ElectrodeTest NotchTest ProbeInfo Connections
Load or save CyberAmp settings.
Make a selection by using the highlighted key for each function. Return to this menu by using <Esc>,
or <Enter> to save the changes made in a submenu.
Setting Up QUICK300
First set up the correct connection to the CyberAmp by choosing Connections. Fill in the dialog form
by moving between cells with the arrow keys and using <PgUp> and <PgDn> to scroll through
options. Be sure that Usage is set to Enabled, to initiate communication with the COM port. Set the
I/O port to the COM port to which the CyberAmp is connected. The device number can be set to
Broadcast if no device number checking is desired. Otherwise, check to see that the device number
entered here corresponds to the device number set on the back panel of the CyberAmp. The serial
- CyberAmp 380 1
- Declaration of Conformity 3
- IMPORTANT INFORMATION 5
- RENSEIGNMENTS IMPORTANTS 6
- WICHTIGE INFORMATIONEN 7
- INFORMACION IMPORTANTE 8
- Explanation of symbols 9
- Explication des symboles 9
- Explicación de símbolos 9
- SÉCURITÉ 10
- SICHERHEITS 10
- HINWEISE 10
- SEGURIDAD 10
- COPYRIGHT 11
- VERIFICATION 11
- TABLE OF CONTENTS 13
- INTRODUCTION 19
- Page 2 INTRODUCTION 20
- INTRODUCTION Page 3 21
- FUNCTIONAL DESCRIPTION 23
- General Features 26
- FUNCTIONAL CHECKOUT 29
- TYPICAL CONFIGURATIONS 33
- Supply Voltage 37
- Changing the Fuse 37
- Grounding and Hum 38
- Power-Supply Glitches 39
- Input Coupling 39
- Expansion 40
- Low-Pass Filter 41
- Amplitude Characteristics 42
- Sampling Rate 43
- 10-90% Rise Time 43
- AC Coupling and Autozeroing 44
- 3 dB frequency of 44
- Time Constant 46
- 100 1.6 46
- Saturation 47
- Notch Filter 48
- Overload Detection 49
- Audio Monitor 50
- External Input 51
- Electrode Test 52
- Strain Gauges 55
- Active Probes 56
- Common-Mode Rejection Ratio 57
- Troubleshooting 59
- TRANSDUCERS 61
- Page 44 TRANSDUCERS 62
- TRANSDUCERS Page 45 63
- EMG, EEG, ECG Recording 64
- Nerve Cuffs 65
- Metal Microelectrodes 65
- Page 48 TRANSDUCERS 66
- Pressure 67
- Acceleration 67
- Self Heating 68
- Isolation 68
- Insulation Techniques 68
- AI 400 SERIES SmartProbes 69
- Transducer Adapter 71
- Input Connector Color Scheme 72
- Recommended Input Coupling 73
- Connector 74
- Example Circuits 75
- Basic Thermistor Circuit 76
- Amplifier Probes 78
- Current Probes 79
- Photodiode Amplifier 79
- Linear Potentiometers 80
- Rotary Potentiometers 80
- Panel Switch 81
- Foot Switch 81
- CMD300 CONTROL SOFTWARE 83
- Command-Line Mode 85
- Interactive Mode 85
- Command-File Mode 86
- Command Reference 87
- CMD300 OVERLOAD 91
- CMD300 REPEAT OVERLOAD 94
- QUICK300 CONTROL SOFTWARE 97
- Command Line Options 100
- CyberControl SOFTWARE 101
- Starting CyberControl 102
- Overload Handling 105
- Keyboard Commands 105
- Communications Settings 107
- PC Menus 108
- Macintosh Menus 109
- PROGRAMMER'S GUIDE 112
- Libraries and Example Code 114
- > end of response 116
- AT3F5 24000 118
- 2 4 6 8 10 ... 28000 30000 118
- AT8R06000 121
- D5=-1234500 124
- Implementation Notes 125
- Support Routine Details 125
- Example Programs 129
- SPECIFICATIONS 135
- Page 118 SPECIFICATIONS 136
- Offset range: ±10 V 137
- Page 120 SPECIFICATIONS 138
- SPECIFICATIONS Page 121 139
- Page 122 SPECIFICATIONS 140
- REFERENCES 141
- ADJUSTMENT PROCEDURES 143
- Other Adjustments 144
- CIRCUIT DIAGRAMS Page 127 145
- SERIAL COMMUNICATIONS CABLES 147
- LIST OF FIGURES AND TABLES 149
- WARRANTY 151
- WARNING 153
- INDEX Page 137 155
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Microsoft LPF-00004
(82 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern